Recent Posts

21

Lobby / Re: Topic replies

« Last post by 5th T/A on May 14, 2024, 04:05:47 PM »

Not to get side tracked but with the detail you put into posts Ben I’d honestly like to see you do a write up sometime on that  RHD conversion and what went into it.

I can’t begin to imagine what a project this would be. Did it require an entire firewall replacement? How did you convert the steering gear box? Heater box and AC case. Under dashboard and under hood wiring. Even an abbreviated explanation would be very interesting.

22

Mechanical / Re: Toasted Clutch

« Last post by 5th T/A on May 14, 2024, 03:42:16 PM »

Many many years ago in the 70’s I worked in a transmission shop. The shop owners had a policy that when we replaced a clutch the flywheel got machined. If it couldn’t get machined it was replaced. This was done because they didn’t want any comebacks. A flywheel with hard spots is more likely to chatter.

23

Mechanical / Re: Toasted Clutch

« Last post by Zach on May 14, 2024, 12:44:57 PM »

The bucking back and fourth usually indicates a warped flywheel. 
If it's the first time its being surfaced it should be okay.  When it gets too thin is when they usually warp easily.

Would make sense, flywheel was the only not so great looking thing. I didn’t check for warpage before I sent it out so hopefully it all gets worked out. I’ll just make sure to get it properly adjusted and all of that. I ordered new pressure plate bolts since someone must’ve changed it at some point it had miss match hardware which I’m sure is not helping, same with the tranny crossover but that’s not as important.

Thanks for all the input.

24

Interior / Re: Console extra holes

« Last post by b_hill_86 on May 14, 2024, 09:42:43 AM »

When I 4 speed swapped my car I bought a reproduction manual console. I’ve never attached it to the dash either. Not that I’m sure it would even attach properly. But it stays out with the screws under the console bin

25

Lobby / Re: Topic replies

« Last post by b_hill_86 on May 14, 2024, 09:39:37 AM »

Not to get side tracked but with the detail you put into posts Ben I’d honestly like to see you do a write up sometime on that  RHD conversion and what went into it.

26

Lobby / Re: Topic replies

« Last post by Wallington on May 14, 2024, 09:10:41 AM »

Haha I'm not sure if it was even here or deleted, was confusing to explain and I gave up. I think.

27

Lobby / Re: Topic replies

« Last post by FormTA on May 14, 2024, 08:34:40 AM »

Man, I missed the seatbelt one. I'll have to go look for it now.

That one actually peaks my interest.

28

Mechanical / Re: Boosting a 301 (for fun)

« Last post by FormTA on May 14, 2024, 08:21:04 AM »

Thanks!

So I spoke with Joe at TTAPERFORMANCE.COM today at great length.  I really appreciate his time and willingness to talk to me about this project. He had some good insights and if anyone doesn't know he is running 13 lbs of boost through the stock internals of his 301. So, we feel safe to run up to 7 lbs on pump gas (he is also running e85 but draw through).

He graciously offered to supply a duel outlet 1981 exhaust manifold to my project.

Well see how this plays out. I'd love to build this as I really think it will be a fun project.

29

Mechanical / Re: Tilt Steering Column

« Last post by wheels78ta on May 14, 2024, 07:57:14 AM »

Thanks for the info.  I was hoping there wasn't too much difference. 

I made an offer and they accepted so the tilt column should be here in a week.

I'll get the kit and make it new again.

30

Mechanical / Re: Tilt Steering Column

« Last post by Wallington on May 14, 2024, 07:18:52 AM »

I'm sure the parts can be swapped over, but one that is already from a manual would be so much easier and be like having spares to select from. These days I'd put a kit through one prior to install, new tilt bushes and the like, paint and install.