Recent Posts

1

Mechanical / Re: Speedo cable

« Last post by DeCaff2007 on Today at 05:01:46 PM »

Under.  There is a detailed thread on the subject dated March below.

Link please.  I'm sorry, but the way that's worded is kind of hard to follow.

2

Exterior / Re: Hood alignment. My next impossible mission.

« Last post by DeCaff2007 on Today at 04:57:30 PM »

Well, I've temporarily moved on from door/fender/hood alignment.  The biggest reason being that I was waiting on radiator support bushings to come in.  I took a look at what I have installed and they just don't look right.

So the parts actually came in today and they look nothing like what's currently installed.



These are what came in today, from Fbodywarehouse. 



Once these get installed, I'll try the door alignment again.  Although, I still don't understand why the driver side door sags down a 1/4" even with new hinges.

Hmm...

3

Interior / Interior progress.

« Last post by DeCaff2007 on Today at 04:43:22 PM »

For at least 10 years now, I've had NO interior, with the exception of the dash and 1 seat.  The reason I tore it all apart was to weld in new floor pans and to give it all a rattlecan. 

Well, a few weekends ago, a neighbor was out walking and I just happened to be working on the T/A in my driveway, because it was nice out.  Said neighbor comes over to chat, and of course we get to talking about cars and all the T/A's he's had in the past. 

Then, said neighbor, in a sort of dismal voice, noted all the work that this T/A needs.

He meant nothing bad by it, but that comment gave me the kick in @$$ I needed to finally get some sound deadening in and carpet laid down.  I've had brand new, correct color (firethorn red) carpet just sitting in the box for years.  Been meaning to get to this for YEARS.  I installed it today.





HUGE difference from just having metal floor pans and that one ragged seat. 

I also have replacement seats that will go in here soon.  I'm waiting on the spring bottoms to come in so I can patch the seats up and bolts them in. 

4

Mechanical / Coolant leak how to fix

« Last post by formula46two on Today at 04:19:46 PM »

Well I topped off the engine with coolant and of course there's a leak. I'm sure it's from letting it sit for so long but I have to take a step back to remedy. I believe it's coming from the rubber seal between the intake and timing cover so question is what is the correct procedure to get a new seal in? Do I leave the timing cover in place and remove the intake or vice versa? Man I didn't need this but gotta deal, right.

5

Number Crunching / Re: 400 casting code

« Last post by rkellerjr on Today at 01:27:59 PM »

Just an FYI, I am running a 500557 block in my car, runs like a banshee, bored .040, forged pistons, roller tip rockers. Used existing crank. Engine was built back in 2009, still running strong! Depends on what you want to do with it. On paper, motor is pushing 400 - 450hp.

6

Tires, Brakes & Suspension / Re: 1981 Rear Disc Brake Parking Brake

« Last post by roadking77 on Today at 01:13:11 PM »

Not sure why my writing did not show up, But I am having a hard time getting my rear calipers hooked up. I have hard lines on the axle and the connection to the caliper is with a banjo bolt. The hard lines DO NOT connect directly to the caliper. In the top pic above you can see the new banjo bolt. In the second pic with the red caliper you can see a 'block' screwed in where the banjo bolt is that accepts the hard line. What is this special fitting called and where can I get a couple?

7

Tires, Brakes & Suspension / Re: 1981 Rear Disc Brake Parking Brake

« Last post by roadking77 on Today at 01:10:44 PM »

Ok.  This is stupid. I spent about 6 weeks fiddling with the stupid parking brake.  Spoiler Alert...It still aint right.
But all the parts are together and they should pass the PA State inspection.

Anyway, I figured I'd close the loop on this thread.

I finally found a picture of an actual marked, LH Caliper:

GM Left Rear caliper by Tom Sherer, on Flickr

I am having a hard time figureing out my rear brakes!! I have hard lines on the axle to the caliper, BUT in the pics shown it looks like instead of a banjo bolt there is some kind of banjo bolt with a square block with threads to accept the hard brake line? Is this a special part/fitting and where can I find one.

  As I suspected, the unmarked caliper on my left rear is wrong. You can see in the pic above how the park brake lever is up around 1 O'clock vs. 7 O'clock on the unmarked caliper I got when I ordered Ames PN FR218EB (now discontinued). 
Untitled by Tom Sherer, on Flickr

The orientation of the lever is determined by a metal 'stop' on the back side of the caliper + the hole that mounts the spring retainer.

Reviewing old GM Parts catalog info, combined with some notes I think came from a pre-crash TAC post from someone more familiar with these parts, I found the GM PN's for these calipers are:
18006748 Caliper Rear(LH)
18006749 Caliper Rear(RH)
And, These calipers were also used on Cadillac Seville's and El Dorado's of the era.

So, to have a properly installed and fully functional e-brake, I need to replace my LH caliper with the correct one.

Finally, I wanted to try to write something about adjusting the parking brake.  'Cause the instructions and video's I found seemed contradictory in some places.  Maybe its just how my brain works.  Here's how I'd describe the adjustment process:

Caliper is on the car.  Pads installed. 
When turning the post/actuator via the inner hex shape, the post will move in and out. There is some sort of ratcheting/clutch voodoo going on inside there.  While the post can push on the piston, it is not directly connected to it.

Because of the way the post moves in and out, you need to install the lever retaining nut onto the post while turning it with an open-end wrench.  The nut prevents the post from pulling too far in so you can't reach the inner hex shape...Like my first problem in this post.

Untitled by Tom Sherer, on Flickr

Turning the post clock-wise pushes the piston outward, clamping the pads to the rotor / actuating the brake.  Keep turning Clock-wise and eventually, the piston will clamp the pads on the rotor.  It'll get tight and wont turn Clockwise anymore.

Turning the post counter Clockwise backs the post off the piston. but, remember it's not connected.  So...it doesn't actually pull the piston back in.  Turning Counter clock-wise works the adjustment mechanism. Because of magical, self-adjusting clutch/ratchet in there, a person could spin and spin and spin Clockwise and not notice any change.  But, there's some sort of ratchet that is the key to adjusting the park brake actuator/lever. 

OK, so...With the nut installed on the post, put a wrench on the inner 9/16 Hex and turn clock-wise until it wont turn anymore. 
Here comes the 'trick'.  The lever needs to fit onto that inner hex shape in a position that leaves no more than 1/8" gap between the lever and the stop on the caliper.   Tighten down clock wise, then turn the post counter clock-wise.  Just a 1/4 turn or so.  You will feel the post try to pull in (but it can't 'cause you have the nut on there) you'll feel some resistance..push past it. That's the magical adjuster doing its job.  Now...turn back CLOCKWISE.  You should notice that your wrench doesn't return quite as far as where you started at before you feel it back to that tight position. 
Repeat this...Turn to tight...Turn 1/4 counter clock-wise...then back to tight. 
This ratcheting action moves the inner hex around. Repeat until is it clocked at the EXACT point where the lever will fit on with no more than 1/8" movement off the stop before it feels tight.

Good Luck!

-Tom

8

Number Crunching / Re: 400 casting code

« Last post by 70_71_78 on Today at 07:33:08 AM »

I have not looked up the block codes, but there were 455 blocks with four bolt main caps that may not have been documented, therefore, few would know about. I bought a thrashed '70 455 auto Bonneville for a 455 to build back in the mid 1980's. Block and engine codes both indicated a standard low performance 4bbl 455. I drove it home and removed the engine and 400 auto trans. Sold the turbo 400, junked the body and frame after removing other usable parts. I started disassembly by removing the entire top end, nothing special there. Rolled it over and pulled the oil pan to find 4 bolt main caps and a nodular iron HO crankshaft! It did not appear that the engine had ever been removed from the car or even opened up for service for that matter. I can only assume that when being built those parts were on the shelf so they used them and assume other anomalies may also exist from that time period. A quick bore size measurement may be in order before passing on it as a builder. I couldn't have been happier with the way mine performed.

9

Tires, Brakes & Suspension / Re: Brake pedal sticking to the floor with delayed release.

« Last post by glhx on May 01, 2024, 07:53:27 PM »

I’m not sure what I could have put in that caliper with a nipple on it to Receive hoses.
That Teflon tape was a tight fit.

The threads took a 3/8 coarse thread bolt.

I think that caliper was pulling in air through the e brake. I’ll know more when I put the new caliper on there.

10

Projects & Restorations / Re: 81 T/A restoration

« Last post by 5th T/A on May 01, 2024, 04:57:45 PM »

Ambitious project and impressive repair work.

Thanks for posting.